Hub, shock absorber and wishbone
rear suspension - new item
Required: 1
crossmember - reproduction
Alternatives
Required: 4
stiffener plate to crossmember
Required: 6
assembly
Required: 2
drive shaft
Part of drive shaft 247349 (ill. 14)
Required: 2
drive shaft, splinted
Part of drive shaft 247349 (ill. 14)
Required: 2
drive shaft - greaseable type with 106.3 mm span width and 30.2 mm cup diameter
Part of drive shaft 247349 (ill. 14)
Required: 4
drive shaft - greaseable heavy duty type with 106.3 mm span width and 30.2 mm cup diameter
Required: 4
drive shaft inner - with grease hole
Required: 2
drive shaft outer - with grease hole
Required: 2
rear suspension. Variant without hole for ABS sensor
Required: 2
rear suspension. Used item without hole for ABS sensor
Required: 2
inner oil seal - rear suspension
Required: 2
rear suspension wheel bearing - inner
Part of wheel bearing kit 202697 (ill. 39)
Required: 2
rear suspension - inner
Part of wheel bearing kit 202697 (ill. 39)
Required: 2
rear suspension - outer
Part of wheel bearing kit 202697 (ill. 39)
Required: 2
- outer
Part of wheel bearing kit 202697 (ill. 39)
Required: 2
for outer oil seal at rear suspension
Required: 2
new item
Required: 2
inner trailing arm - this kit services one side of the vehicle
Required: 2
trailing arm
Part of rebuilt kit 214966 (ill. 45)
Required: 8
trailing arm
Part of rebuilt kit 214966 (ill. 45)
Required: 4
trailing arm bearing - inner
Part of rebuilt kit 214966 (ill. 45)
Required: 8
inner trailing arm bearing
Part of rebuilt kit 214966 (ill. 45)
Required: 8
for the sealing ring of the inner trailing arm bearing
Part of rebuilt kit 214966 (ill. 45)
Required: 8
trailing arm - outer
Part of rebuilt kit 214966 (ill. 45)
Required: 8
inner trailing arm retaining
Part of rebuilt kit 214966 (ill. 45)
Required: 4
retaining trailing arm bracket - length: 22 mm (7/8")
Required: 2
retaining trailing arm bracket - length: 10 mm (7/16")
Required: 2
rear suspension, LH
Required: 1
outer trailing arm
Series I - Series II 4.2 Saloon to 2T22972, 2T68823, 2S10116 and 2S50581 - Series II USA and Canada exports to 2T69450 - Series II 3.4 to 3A5115, 3A51460, 3B3226 and 3B50004 - Series III Vanden Plas to 3C1698 and 3C50011
Required: 2
outer trailing arm
XJ6 (1977-87) - Series II 4.2 Saloon from 2T22973, 2T68824, 2S10117 and 2S50582 - Series II USA, Canada and Japan models from 2T69451 - Series II 3.4 ab 3A5116, 3A51461, 3B3227 and 3B50005 - Series II Vanden Plas from 3C1699 and 3C50012 – plus all Series III models
Required: 2
XJ6 (1977-87) - Series II 4.2 Saloon from 2T22973, 2T68824, 2S10117 and 2S50582 - Series II USA, Canada and Japan models from 2T69451 - Series II 3.4 ab 3A5116, 3A51461, 3B3227 and 3B50005 - Series II Vanden Plas from 3C1699 and 3C50012 – plus all Series III modelss
Required: 4
shock absorber
XJ6 (1977-87) - Series II 4.2 Saloon from 2T22973, 2T68824, 2S10117 and 2S50582 - Series II USA, Canada and Japan models from 2T69451 - Series II 3.4 ab 3A5116, 3A51461, 3B3227 and 3B50005 - Series II Vanden Plas from 3C1699 and 3C50012 – plus all Series III models
Required: 2
outer trailing arm - this kit services one side of the vehicle
Required: 2
trailing arm - 0.003"
Part of rebuilt kit 214967 (ill. 63)
Required: 2
trailing arm - 0.007"
Part of rebuilt kit 214967 (ill. 63)
Required: 2
trailing arm felt seal
Part of rebuilt kit 214967 (ill. 63)
Required: 2
trailing arm felt seal
Part of rebuilt kit 214967 (ill. 63)
Required: 4
for outer trailing arm bearing
Part of rebuilt kit 214967 (ill. 63)
Required: 4
trailing arm bearing
Part of rebuilt kit 214967 (ill. 63)
Required: 4
trailing arm bearing, outer position
Part of rebuilt kit 214967 (ill. 63)
Required: 4
trailing arm outer
Part of rebuilt kit 214967 (ill. 63)
Required: 4
trailing arm outer
Required: 4
trailing arm - 0.003"
Part of rebuilt kit 214967 (ill. 63)
Required: 2
0.007"
Part of rebuilt kit 214967 (ill. 63)
Required: 2
trailing arm outer
Part of rebuilt kit 214967 (ill. 63)
Required: 2
Part of rebuilt kit 214967 (ill. 63)
Required: 4
rear
Required: 4
rear - gas-charged damper with spring seat adjustment
Required: 4
rear shock absorber upper and lower mounting
Required: 4
rear shock absorber upper and lower mounting. Variant with inner sleeve
Required: 8
upper shock absorber mounting
Required: 4
upper shock absorber mounting
Required: 4
lower shock absorber mounting
Series I - Series II 4.2 Saloon to 2T22972, 2T68823, 2S10116 and 2S50581 - Series II USA and Canada exports to 2T69450 - Series II 3.4 to 3A5115, 3A51460, 3B3226 and 3B50004 - Series III Vanden Plas to 3C1698 and 3C50011
Required: 2
lower shock absorber mounting
Series I - Series II 4.2 Saloon to 2T22972, 2T68823, 2S10116 and 2S50581 - Series II USA and Canada exports to 2T69450 - Series II 3.4 to 3A5115, 3A51460, 3B3226 and 3B50004 - Series III Vanden Plas to 3C1698 and 3C50011
Required: 2
lower shock absorber mounting
Series II 4.2 Saloon from 2T22973, 2T68824, 2S10117 and 2S50582 - Series II USA, Canada and Japan exports from 2T69451 - Series II 3.4 from 3A5116, 3A51461, 3B3227 and 3B50005 - Series III Vanden Plas from 3C1699 and 3C50012 - Series II Coupe - all Series III models
Required: 4
lower shock absorber mounting
Required: 2
spring seat 'rear coil spring - 1 half. Fits to genuine Jaguar dampers only
Required: 8
spring seat 'rear coil spring - 1 half. Fits to Limora damper 200448 and 1579 only
Required: 8
rear suspension - high quality reproduction including rubber bushes
Required: 2
rear suspension - high quality reproduction with OE Metalastic rubber bushes
Required: 2
rear suspension - high quality reproduction including uprated 'Comfort' polyurethane bushes
Required: 2
rear suspension - high quality reproduction including uprated 'Race' polyurethane bushes
Required: 2
rear - high quality reproduction, supplied without bushes
Required: 2
rear radius arm, front
Alternatives
Required: 2
rear radius arm, front - uprated 'comfort' type
Alternatives
Required: 2
1.7/8" x 7/16 UNF with hole for lock wire - radius arm bracket to chassis. Please note: must be used with thread lock at the point of assemble
Required: 2
securing bolt 208155 (ill. 94)
Supplied per meter
Required: 1
rear radius arm, rear. Uprated 'comfort' type
Alternatives
Required: 2
